Recessed Light Spacing and How Many You Need in a Room
Recessed lights put in the wrong places give you a ceiling that looks like a runway and a room with bright circles on the floor and gloomy corners.

Recessed lights put in the wrong places give you a ceiling that looks like a runway and a room with bright circles on the floor and gloomy corners. Getting recessed light spacing right before anyone cuts a hole is the difference between a room that feels evenly lit and one you end up adding lamps to.
I plan lighting layouts for homeowners and renovators, and the same few mistakes come up again and again. This guide gives you the simple spacing rules, a worked example, and the safety points to raise with your electrician before installation day.
The basic recessed light spacing rule
The most common starting point is this: divide the ceiling height by two to get the spacing between lights. A standard 8 foot (2.4 m) ceiling gives you lights about 4 feet (1.2 m) apart. A 10 foot (3 m) ceiling gives you about 5 feet (1.5 m).
The second rule covers the walls. Keep the first row of lights roughly half that spacing from the wall, usually 2 to 3 feet (60 to 90 cm). Closer than that and you get harsh scallops of light down the wall. Further away and the edges of the room fall into shadow.
These numbers assume typical modern LED downlights of 4 to 6 inches with a beam angle around 60 degrees. Narrow beam fittings of 30 to 40 degrees need to sit closer together. Wide beam fittings of 90 degrees or more can be spaced further apart.
High and sloped ceilings
The half the ceiling height rule still works on a 9 or 10 foot ceiling, but light spreads further before it reaches the floor, so each fitting covers more area and you may need slightly higher output, around 900 to 1,200 lumens, to keep the room bright at table height. On a sloped or vaulted ceiling, use sloped ceiling trims or adjustable gimbal fittings so the beam points straight down rather than across the room. Measure spacing along the floor, not along the slope, otherwise lights on the steep part of the ceiling end up too far apart. For ceilings above 12 feet, a mix of downlights and wall lights usually works better than downlights alone, and changing a lamp up there needs a proper platform or tower, so choose long life fittings.
How many recessed lights you need in a room
Spacing tells you the grid. Brightness tells you whether that grid is enough. A useful guide is the amount of light needed per square foot of floor:
| Room | Lumens per square foot | Example for a 12 x 14 ft room (168 sq ft) |
|---|---|---|
| Living room | 10 to 20 | 1,700 to 3,400 lumens |
| Bedroom | 10 to 20 | 1,700 to 3,400 lumens |
| Kitchen general lighting | 30 to 40 | 5,000 to 6,700 lumens |
| Bathroom | 50 to 75 | Usually a smaller room, so fewer fittings |
| Home office | 30 to 50 | 5,000 to 8,400 lumens |
Divide the target lumens by the output of the fitting you plan to buy. Most 6 inch LED downlights produce 700 to 1,000 lumens. So a living room needing about 2,800 lumens works out to four fittings of 700 lumens each.
A worked example
Take a 12 by 14 foot living room with an 8 foot ceiling. Spacing is about 4 feet, and the first lights go about 2 to 3 feet from the walls.
- Along the 14 foot wall: 3 feet in, then 4 feet, 4 feet, leaving 3 feet. That is three lights.
- Along the 12 foot wall: 3 feet in, then 6 feet, leaving 3 feet. That is two lights.
- Total: a grid of six lights, about 4,200 lumens with 700 lumen fittings.
That is more than the room strictly needs, which is fine as long as they sit on a dimmer. If you choose a dimmer, match it to the LEDs, or you may end up with the problems covered in why LED bulbs flicker on a dimmer and how to fix it.
The counter-take: do not fill the ceiling with a perfect grid
A lot of layout advice stops at the grid. Follow it rigidly in every room and you get the flat, office like look that makes so many renovated homes feel cold. I would rather see fewer recessed lights placed with purpose.
Think about what the light is for. In a kitchen, place lights over the front edge of the worktops, around 24 to 30 inches out from the wall, so you are not working in your own shadow. In a living room, two or three lights washing a feature wall or bookcase can do more than six over the middle of the floor. Put lamps and wall lights alongside them for warmth. Our guide on how to light a room properly explains how general, task and accent lighting work together.
Fewer holes also means fewer penetrations through the ceiling, which matters for insulation and air leakage in top floor rooms.
Safety points to check before installation
Recessed lights are simple fittings, but they sit inside the ceiling void, close to joists, cables and insulation. In most places, new lighting circuits and fittings must be installed by a qualified electrician or inspected under local rules. Before work starts, ask about these:
- Insulation contact rating. Under an insulated loft or roof, use fittings rated for direct contact with insulation, often marked IC in North America. Non rated fittings need clearance and can overheat if insulation is packed around them.
- Fire rated fittings. Where a ceiling separates a room from a floor above, building rules may require fire rated downlights to maintain the ceiling's fire resistance.
- Joist positions. Find joists before marking the layout. Moving a light by 5 cm to miss a joist is fine. Cutting into a joist is not.
- Circuit load. LED fittings draw very little, often 8 to 12 watts each, so load is rarely the problem. The wiring route and connections matter far more.
- Bathroom zones. Fittings over or near a bath or shower need an appropriate moisture rating for their position.
Choose one colour temperature for all the fittings in a room so the light looks consistent. Our LED color temperature guide covers which temperatures suit each space.
Frequently asked questions
How far apart should 6 inch recessed lights be?
On a standard 8 foot ceiling, about 4 feet apart is a good starting point, with the first row 2 to 3 feet from the walls. Adjust slightly for beam angle. Wider beams can go a little further apart, narrower beams a little closer.
How far should recessed lights be from the wall?
Usually 2 to 3 feet from the wall for general lighting. If you want to highlight artwork or a textured wall, move them closer, around 12 to 18 inches, and use adjustable or wall washing fittings.
Is it better to have more or fewer recessed lights?
More, lower output fittings on a dimmer give smoother light than a few very bright ones, but filling the ceiling with a strict grid can look flat. Aim for enough lights to reach your target brightness and add lamps or wall lights for warmth and contrast.
More in Lighting
Lighting
Replacing Fluorescent Tubes With LED the Right Way
The two four-foot fixtures in my basement laundry area took about four seconds to come on, hummed the whole time, and one of...
Lighting
Home Office Lighting That Cuts Screen Glare and Eye Strain
By three in the afternoon, a lot of people working from home have a dull headache behind the eyes and assume it is the screen.
Lighting
Bathroom Lighting and Which Fixtures Are Safe Near Water
You found a pendant you love for over the tub, or a pretty sconce for the shower wall, and now you are wondering whether it is...