Bathroom Lighting and Which Fixtures Are Safe Near Water
You found a pendant you love for over the tub, or a pretty sconce for the shower wall, and now you are wondering whether it is actually allowed there.

You found a pendant you love for over the tub, or a pretty sconce for the shower wall, and now you are wondering whether it is actually allowed there. Bathroom lighting is the one place in the house where a fixture's rating matters as much as its looks, because steam, splashes and wet hands all meet live electricity in a small space.
The good news is that the rules are not complicated once you know the three ratings and the one clearance zone that everything hangs on. This guide covers which fixture goes where, how bright each layer should be, and when you need an electrician rather than a weekend.
Bathroom lighting ratings: dry, damp and wet
Every listed light fixture sold in North America carries a location rating on its box or label. In a bathroom you will see three.
- Dry rated. Built for ordinary rooms. Fine for a large bathroom's far corner or a separate toilet room with good ventilation, but not near the tub or shower.
- Damp rated. Built to handle humidity and condensation, but not direct water spray. This is the standard choice for vanity lights and general ceiling lights in most bathrooms.
- Wet rated. Sealed against water that can hit the fixture directly. Required for lights inside a shower enclosure or directly over the tub where spray can reach.
If the box does not say damp or wet, assume dry. A fixture listed by a recognized testing lab will state its rating clearly, and a fixture with no listing mark at all should not be in a bathroom.
The zone around the tub and shower
The national electrical code sets out a space around the tub and shower where certain fixtures are not allowed. It extends 3 feet horizontally from the tub rim or shower threshold, and up to 8 feet vertically above that rim or threshold.
Inside that space, you cannot install:
- Hanging fixtures on cords, chains or cables, such as pendants and chandeliers
- Track lighting
- Ceiling paddle fans
- Lighting on a lighting track or bus system
That is why the dramatic chandelier over a freestanding tub in magazine photos is usually either hung very high, in a room with a tall ceiling, or simply not up to code. A recessed light or a close mounted ceiling fixture is the usual answer inside the zone, and if it is in the direct spray path it must be wet rated. Many manufacturers also require that a fixture installed over a shower or tub be protected by a GFCI, so read the instruction sheet.
Local codes can add stricter rules, so check with your building department before you start any new circuit or fixture location.
How bright each layer should be
A bathroom needs task light at the mirror first, then general light for the room, then optional accent or night lighting. As rough targets for a typical 40 to 60 square foot bathroom:
| Layer | Typical fixture | Approximate output |
|---|---|---|
| Vanity task | Sconces either side of the mirror or a bar above | 1,500 to 2,000 lumens total |
| General | Damp rated ceiling fixture or two recessed lights | 1,000 to 1,500 lumens |
| Shower | Wet rated recessed light | 600 to 800 lumens |
| Night | Low toe kick strip or plug-in night light | 20 to 50 lumens |
For skin tones that look right in the mirror, choose bulbs between 2700K and 3000K with a color rendering index of 90 or higher. If you are adding recessed cans, our guide on recessed light spacing shows how to plan the layout so you do not end up with a bright spot over the toilet and a dark tub.
Why a single overhead light over the mirror is a mistake
The most common advice for a small bathroom is to fit one bright light bar above the mirror and call it done. It is cheap, it is quick, and a lot of builders still do it.
The problem is the angle. Light from directly above the mirror falls straight down onto your face, which throws shadows under your eyes, nose and chin. That is exactly where you need to see when shaving or putting on makeup. Sconces mounted on either side of the mirror, roughly at eye level, around 60 to 66 inches from the floor and about 36 to 40 inches apart, light the face evenly from the front.
If the wall layout only allows an overhead bar, choose one at least 24 inches long, mount it a few inches above the mirror, and use a frosted diffuser rather than bare bulbs. It is a compromise, but a far better one than a single small fixture.
Ventilation fans with lights and moisture in the box
A combination exhaust fan and light is a smart choice for small bathrooms, because it puts the general light and the fan in one ceiling opening. Check two things on the label. First, if it sits over the tub or shower, it must be listed for that location, and many models are listed only when they are on a GFCI protected circuit. Second, size the fan for the room. A common rule is at least 1 cubic foot per minute of airflow per square foot of floor, so a 50 square foot bathroom needs a fan of 50 CFM or more.
A fan that actually clears steam protects every fixture in the room. Run it during the shower and for about 20 minutes afterward. Condensation that sits inside a ceiling box night after night is one of the quiet causes of corroded terminals and flickering lights in older bathrooms.
Safe swaps you can do and jobs to leave alone
Replacing a vanity light with another fixture of the same type, in the same spot and on the same circuit, is a reasonable job for a careful homeowner. The basic rules:
- Turn off the breaker, not just the wall switch, and confirm the power is off with a non-contact tester.
- Check that the new fixture's rating suits the location and that the electrical box is secure and properly sized.
- Seal around the fixture canopy with the gasket supplied, if there is one, to keep moisture out of the box.
- Restore power and test.
Moving a fixture into the tub zone, adding a light inside the shower, or running a new circuit are jobs for a licensed electrician. So is any situation where you find aluminum wiring, scorched insulation or a box with no ground. For broader advice about planning fixtures room by room, see how to choose the right lighting for each room, and browse the rest of our lighting guides.
Frequently asked questions
Can you put a regular light fixture in a bathroom?
A dry rated fixture is only acceptable in parts of the bathroom well away from steam and spray, and many electricians avoid them entirely. Damp rated fixtures are the safer default for vanity and ceiling lights. Anything within the reach of shower spray must be wet rated.
Does bathroom lighting need to be on a GFCI?
Bathroom receptacles must be GFCI protected, and fixtures over a tub or inside a shower often require GFCI protection by their own instructions. Many electricians protect the whole bathroom circuit for simplicity. Check the fixture instructions and your local code.
Can I hang a pendant light over a bathtub?
Not within 3 feet horizontally and 8 feet vertically of the tub rim, under the national electrical code. In a room with a very high ceiling the pendant may sit above that zone. Otherwise, use a close mounted or recessed fixture with the right damp or wet rating.
More in Lighting
Lighting
Replacing Fluorescent Tubes With LED the Right Way
The two four-foot fixtures in my basement laundry area took about four seconds to come on, hummed the whole time, and one of...
Lighting
Home Office Lighting That Cuts Screen Glare and Eye Strain
By three in the afternoon, a lot of people working from home have a dull headache behind the eyes and assume it is the screen.
Lighting
Recessed Light Spacing and How Many You Need in a Room
Recessed lights put in the wrong places give you a ceiling that looks like a runway and a room with bright circles on the floor...