Does a Microwave Need a Dedicated Circuit in Your Kitchen
The breaker trips every time the microwave and the kettle run together, and you are left standing in a dark kitchen corner resetting the panel again.

The breaker trips every time the microwave and the kettle run together, and you are left standing in a dark kitchen corner resetting the panel again. That is often the first sign of a question many homeowners never think to ask: does a microwave need a dedicated circuit, or can it share with everything else on the counter?
The short answer depends on the type of microwave and what your installation instructions say. Here is how to work it out for your own kitchen, with real numbers, and when it is time to call a licensed electrician.
How much power a microwave actually draws
The wattage printed on the front of a microwave is its cooking power, not what it pulls from the wall. Magnetrons are only about 60 to 65 percent efficient, so the input power is much higher. Check the rating label inside the door or on the back for the true figure.
| Microwave type | Cooking power | Typical input power | Current at 120 V |
|---|---|---|---|
| Small countertop | 700 W | 1,050 to 1,150 W | 9 to 10 A |
| Standard countertop | 1,100 W | 1,500 to 1,700 W | 12.5 to 14 A |
| Over the range | 1,000 W | 1,500 to 1,650 W | 12.5 to 14 A |
| Built-in or drawer | 950 to 1,200 W | 1,500 to 1,800 W | 12.5 to 15 A |
Now add the neighbours. A kettle draws about 12 A. A toaster draws 7 to 10 A. A standard 20 A kitchen circuit can carry those loads for short bursts, but a 1,100 W microwave plus a kettle is roughly 26 A, which will trip a 20 A breaker within seconds or minutes. That trip is the breaker doing its job, not a fault.
When does a microwave need a dedicated circuit
In the United States, the National Electrical Code requires at least two 20 A small appliance circuits for kitchen countertop receptacles. It does not name microwaves specifically. What it does require is that appliances be installed according to their listing and the manufacturer's instructions. That is where the real rule usually comes from.
- Over the range and built-in microwaves. Almost every installation manual calls for a dedicated 15 A or 20 A circuit, often specifying a 20 A circuit with 12 gauge copper wire. Inspectors enforce this because the instructions are part of the code.
- Countertop microwaves. These are portable appliances and can plug into a countertop small appliance circuit. Many manuals still recommend a separate circuit, and in practice a heavy user will be happier with one.
- Local rules. Some jurisdictions add their own requirements. Your local building department can tell you what applies in a remodel.
Outside North America the numbers change. On 230 V systems, a 1,700 W microwave draws only about 7.4 A, so a single ring or radial circuit usually copes. The principle still applies: follow the installation manual, and do not stack several heating appliances on one outlet.
Signs your current setup is overloaded
You do not need test equipment to spot most problems. Watch for these:
- The breaker trips when the microwave runs alongside a kettle, toaster or coffee maker.
- Kitchen lights dim noticeably when the microwave starts.
- The outlet face or the plug feels warm after a few minutes of use.
- You see discoloration, a brown tint, or a faint burnt plastic smell near the outlet.
- The microwave is plugged into a power strip or extension cord because the outlet is out of reach.
A warm outlet or burnt smell is not an overload you can live with. Stop using that outlet and have it checked. Loose terminals heat up under heavy loads and are a known fire start. Our guide on why an overloaded power strip overheats in the kitchen explains what happens inside the strip.
Map the circuit before you call anyone
Switch the microwave's breaker off and walk the kitchen with a lamp or an outlet tester to see what else went dead. Write it down. If the same circuit feeds the microwave, the toaster outlet and the dishwasher, you have found the problem in five minutes, and the electrician's quote will be faster and cheaper. Label the panel while you are there, since most kitchen panels in older homes carry vague or wrong labels.
Why a bigger breaker is never the fix
Some people swap the 20 A breaker for a 30 A one to stop the tripping. This is one of the most dangerous changes you can make. The breaker protects the wire in the wall, not the appliance. A 12 gauge copper wire is rated for 20 A. Push 28 A through it for long enough and the insulation softens and burns inside the wall, where you cannot see it.
The other common advice is to "just stop using two things at once." That works, but I think it sells people short. If you are rearranging your morning routine around a breaker, the circuit is undersized for how you live, and a dedicated microwave circuit is a modest job that removes the problem for good.
What adding a dedicated circuit involves
This is work for a licensed electrician, and in most areas it needs a permit and inspection. Here is roughly what to expect so you can judge a quote.
- A new 20 A breaker in the panel, assuming there is a free space. If the panel is full, the electrician may need tandem breakers or a subpanel.
- A run of 12 gauge cable from the panel to the microwave location, through walls, attic or basement.
- A new receptacle, which may need GFCI protection depending on its location and your local code. Many newer codes also require AFCI protection on kitchen circuits.
- Typical cost in the US is $250 to $800 for an easy run, more if walls need opening or the panel needs work.
If the breaker keeps tripping on circuits without heavy appliances, the cause may be different. Our article on what an AFCI breaker does and why it keeps tripping covers the other common culprit.
Frequently asked questions
Can a microwave and refrigerator be on the same circuit?
It is best avoided. A refrigerator compressor draws a surge when it starts, and if the microwave is running at the same moment the breaker may trip and leave the fridge off without you noticing. Many manufacturers recommend a separate circuit for each.
Can I plug a microwave into an extension cord?
Manufacturers advise against it. Most household extension cords are not rated for a continuous 13 to 15 A load, and the plug connections can overheat. Move the microwave nearer an outlet or have an outlet added where you need it.
What size breaker does a microwave need?
Most microwaves run on a 15 A or 20 A circuit, and over the range models usually specify 20 A. The breaker must match the wire gauge, so a 20 A breaker needs 12 gauge copper wire. Your installation manual gives the exact requirement.
More in Appliances
Appliances
Dishwasher Energy Use and the Cycle That Saves Most
Your dishwasher is the appliance people feel guilty about.
Appliances
Standby Power: Which Appliances Still Cost You Money
I bought a plug-in power meter for $22 last spring because I was tired of guessing.
Appliances
Refrigerator Energy Use and How to Lower It at Home
Your electricity bill crept up and you suspect the fridge, because it is the one appliance that never switches off.