Light Fixture Wattage Limits and Enclosed LED Bulbs
A reader wrote to me in February about a hallway light that had eaten three LED bulbs in fourteen months. She had bought the expensive ones the second time, kept the receipt, and was planning to complain to the manufacturer.

A reader wrote to me in February about a hallway light that had eaten three LED bulbs in fourteen months. She had bought the expensive ones the second time, kept the receipt, and was planning to complain to the manufacturer. The fixture was a glass dome screwed flush to the ceiling, the kind fitted in about half the hallways built since 1990, and the bulbs were ordinary A19 LEDs with no marking about enclosed fittings.
Nothing was defective. The dome was running at an internal temperature the bulbs were never designed to survive, and the sticker inside the fixture, the one that says maximum 60 watts, was telling her something she had reasonably assumed no longer applied. That sticker is the most misunderstood label in a house. It has almost nothing to do with your electricity bill and everything to do with how hot a sealed space gets.
What the wattage sticker is actually measuring
When a fixture is tested for listing, it is run with the largest incandescent lamp the maker intends, and the temperature is measured at the socket shell, at the wire terminals and on the wiring inside the canopy. The limit printed on the label is the wattage at which those temperatures stay inside the rating of the materials around them.
The materials are the point. Older fixtures were wired with conductors rated for 60 degrees Celsius, newer ones usually 90 degrees. Run a 100 watt incandescent in a fixture rated for 60 and the socket can sit well above 150 degrees for hours. Nothing dramatic happens that evening. What happens over several years is that the insulation on the fixture wires goes hard and brown, cracks when anybody moves it, and eventually lets two conductors touch. That failure arrives long after the person who fitted the wrong bulb has moved house.
If you unscrew a ceiling fixture and find stiff, discoloured wire with a smell like burnt bakelite, somebody overlamped it. That fixture needs replacing rather than rewiring, and it belongs on the list of things in the guide to electrical warning signs you should never ignore.
Why LED bulbs die in enclosed fittings
Here is the part that catches careful people. An incandescent bulb throws most of its waste heat outward as infrared, away from the socket. An LED does the opposite. The light emitting part runs comparatively cool, and the heat is dumped backwards into the aluminium body of the bulb, which is why LED bulbs have those finned or ribbed bases. They are heat sinks.
Sitting directly behind that heat sink is the driver, a small circuit board with electrolytic capacitors on it. Capacitors are the shortest lived component in the bulb and their life roughly halves for every 10 degree rise in temperature. In open air the arrangement works. Inside a sealed glass dome, the heat the bulb is trying to shed has nowhere to go, the air around the driver stabilises 20 or 30 degrees above room temperature, and the 25,000 hour rating on the box turns into something closer to 5,000.
Most LED bulbs carry a maximum ambient temperature on the packaging, commonly 40 or 45 degrees Celsius, and many state in small print that they are not suitable for use in totally enclosed fixtures. A smaller number are explicitly rated for enclosed use, with a bigger heat sink and a driver specified for higher temperatures, and those are the ones to buy for a dome.
| Fixture type | Air around the bulb | What to fit |
|---|---|---|
| Open shade, table lamp, pendant | Close to room temperature | Any LED of the right shape |
| Flush ceiling dome, sealed glass | Typically 15 to 30 degrees above the room | Enclosed rated LED only |
| Outdoor sealed lantern | Hot in summer sun, cold in winter | Enclosed rated, with the stated temperature range checked |
| Bathroom fitting with a sealed diffuser | Hot and humid together | Enclosed rated, and damp location listed |
The reader with the hallway dome swapped to an enclosed rated bulb at about four dollars more than the one she had been buying. It has been in since March.
Why the advice to ignore the sticker is half right and still dangerous
You will read everywhere that wattage limits no longer matter because LEDs use so little power. A 9 watt LED makes the light of a 60 watt incandescent, 9 is less than 60, so fit whatever you like. As a statement about the sticker, that is correct. As advice, it quietly removes the only thing in the house that was telling people to think about heat.
Two problems follow from it. The first is that the limit has not disappeared, it has moved. The old limit was about how hot the bulb made the fixture. The new limit is about how hot the fixture makes the bulb, and nobody prints that one on the ceiling. A person who learns that the sticker is obsolete has no reason to look for the words enclosed fixture on a box, and so buys the wrong bulb repeatedly and blames the brand.
The second problem is the houses where the sticker still matters exactly as written. Plenty of lamps and fixtures still take halogen or incandescent, especially small candle lamps, oven and appliance bulbs, and decorative fittings where people prefer the filament look. Those are the ones where somebody reaches for the 60 watt because it is in the drawer and the fixture says 40.
My own rule is shorter than either piece of advice. Read the sticker for incandescent and halogen as a hard ceiling, and for LED read the bulb box instead of the fixture. One of the two labels always applies.
Recessed cans, insulation, and the light that clicks off
Recessed cans are where heat turns into a genuine safety question rather than a bulb lifespan question. Housings come in two sorts. An IC rated can is built so thermal insulation may sit directly against it. A non IC can must have a clear gap, commonly three inches, around and above the housing, and plenty of homes have non IC cans buried under blown cellulose by a contractor working in a loft who was never told the difference.
Every can made for decades now has a thermal protector inside, a small switch that cuts the lamp when the housing gets too hot and restores it when it cools. So the classic symptom is not a fire. It is a recessed light that goes off after twenty minutes and comes back ten minutes later, and gets diagnosed as a loose bulb or a bad switch. It is neither. It is a device doing its job and telling you the housing is overheating.
If that is happening, the honest options are to get into the loft and clear insulation back from the housing, or to fit a sealed LED retrofit module designed for recessed cans. The modules are a real improvement because total heat drops and because most of them seal the hole, which stops warm indoor air leaking into the loft. They run roughly 12 to 25 dollars each. If you are planning new cans rather than fixing old ones, the layout side of the job is covered in the guide to recessed light spacing and how many you need.
One thing I would not do is remove a thermal protector or tape it over, which I have genuinely been asked about. That switch is the last line between trapped heat and a joist.
A twenty minute check, room by room
Find the stickers before you buy anything. Ceiling fixtures carry the label inside the canopy or on the socket bracket, visible once the shade is off. Note the number and whether the fitting is sealed. Five fixtures takes about ten minutes and ends the guessing.
Read the small print on the bulb box, not the front. The front says 60 watt equivalent and 25,000 hours. The side panel says the ambient temperature range and whether enclosed use is permitted. If a box says nothing about enclosed fixtures, assume it is not suitable.
Note any light that switches itself off and on. In a recessed fitting that is the thermal protector. In a flush fixture it is often the LED driver's own overheat protection. Either way it is a heat message, not a wiring fault.
Check the dimmer pairing while you are there. A non dimmable LED on a dimmer circuit runs its driver outside spec and fails early, often with a buzz or a flicker first. Match the bulb to the control or replace the switch with a plain one. Colour and quality choices are a separate matter, set out in the guide to LED colour temperature for every room.
If you find charred wiring, a socket that has gone brittle, or scorch marks on a ceiling around a can, stop and get an electrician in. A service call runs around 150 to 250 dollars in most areas and replacing a fixture is usually inside that visit. The wider habits worth keeping are collected in the electrical safety guides.
Frequently asked questions
Can I put a 100 watt LED equivalent in a 60 watt fixture?
Yes, as long as the bulb's actual draw is under 60 watts, which for an LED it will be. The real question is whether the fixture is sealed, because an enclosed fitting needs a bulb rated for enclosed use regardless of wattage.
Why do my LED bulbs keep burning out in one fixture?
Almost always trapped heat cooking the driver, and almost always in a sealed dome, a recessed can or an outdoor lantern. Switching to a bulb marked suitable for enclosed fixtures fixes it more often than switching brands.
What does an enclosed fixture rated bulb actually change?
A larger heat sink and components specified for a higher ambient temperature, usually with a stated limit of 50 degrees Celsius or more. They cost a few dollars more and last several times longer in a dome.
Why does my recessed light turn off by itself?
The thermal protector in the housing is cutting power because the can is overheating, often because insulation is pressed against a housing not built for it. Clear the insulation or fit a retrofit module rated for the can.
More in Electrical Safety
Electrical Safety
Christmas Light Safety Checks Before You Plug In
Every year around the second week of December someone sends me a photo of a power strip behind a tree with four plugs in it, a...
Electrical Safety
Electric Shock First Aid and What to Do in the First Minute
Someone in your home has just touched a faulty lamp or a frayed cord and is either frozen against it or lying on the floor, and...
Electrical Safety
Smoke Detector Placement and the Rooms That Need One
A smoke alarm in the wrong spot either screams every time you make toast or stays silent until a fire is already well under...