Three-Way Switch Wiring and Why One Switch Stops Working
A reader wrote to me last spring about her stairway light. It worked from the bottom switch, and it worked from the top switch, but only if the bottom one was in a particular position.

A reader wrote to me last spring about her stairway light. It worked from the bottom switch, and it worked from the top switch, but only if the bottom one was in a particular position. Flip the bottom switch "wrong" and the top switch did nothing at all. A handyman had replaced both switches the month before, and the problem started that day.
That symptom has a cause in nine out of ten cases I have seen, and it is not a faulty switch. It is one wire on the wrong screw. Three-way switch wiring looks confusing because there are more wires than on an ordinary switch, but once you know which wire does what, both the fault and the fix become fairly obvious.
How two switches share one light
An ordinary single-pole switch has two brass screws. It simply breaks or completes one hot wire. A three-way switch has three terminals: one darker screw, usually black or bronze, called the common, and two lighter brass screws called the travelers.
Inside, the switch does not turn anything off. It connects the common terminal to one traveler or the other. Flip it, and the path moves from traveler A to traveler B.
At one switch, the common connects to the incoming hot from the panel. At the other switch, the common connects to the wire going to the light. Between the two switches run two traveler wires. The light is on when both switches select the same traveler, and off when they select different ones. That is why either switch can change the state of the light at any time.
For this you need a three-conductor cable between the switches, labelled 14/3 for a 15 amp circuit or 12/3 for a 20 amp circuit. It contains black, red and white insulated wires plus a bare ground. The black and red usually serve as the travelers. The white is often used as the neutral to the light, or, in older wiring where the power enters at the light, it may carry hot and should be marked with black or red tape. My guide to what wire colours mean goes into the re-marking rule.
Why the light only works in some combinations
Here is the reader's problem written out. If the common wire and one traveler swap places at one switch, the circuit still sometimes completes, which is what makes the fault so confusing.
| Bottom switch | Top switch | Correct wiring | Common swapped with a traveler |
|---|---|---|---|
| Up | Up | On | On |
| Up | Down | Off | Off |
| Down | Up | Off | Off |
| Down | Down | On | Off, and the top switch does nothing |
When a switch is replaced, the old one often has the common in a different position from the new one. Brands differ. A Leviton switch might have the common on the lower left, a Legrand on the upper right. Anyone who copies the old switch by position rather than by screw colour moves the common onto a traveler screw without noticing.
So when a three-way pair starts misbehaving after a replacement, the first suspect is the switch that was swapped, and specifically which wire landed on the dark screw.
Finding the common safely
Before touching anything, switch off the circuit breaker for that light. Then check with a non-contact voltage tester at both switch boxes. Stairway lights are sometimes fed from a different circuit than you expect, and in older homes two circuits can share a switch box. If you have any doubt about which breaker feeds which box, stop and read our page on when to call an electrician.
With the power off, pull the switch out and look at the cables entering the box. At a typical three-way switch you will see one two-conductor cable and one three-conductor cable, or two three-conductor cables if power passes through. The wire that is not part of the three-wire run between switches is your common, or it joins the common under a wire nut with a pigtail.
If the labels are gone and the wiring is unclear, you can identify the common with a multimeter and a careful live test, but that means working with exposed hot conductors. I do not recommend it for anyone without training. A licensed electrician will usually sort this out in under an hour, and the bills I have seen for this exact fault ranged from about $95 to $180.
The usual tip to just buy smart switches
A lot of advice online says the easy way around three-way wiring is to replace both switches with a smart switch and a wireless remote. Sometimes that is good advice. It is not always the shortcut it sounds like.
Most smart three-way kits need a neutral wire in the main switch box, and many stairway boxes in homes built before about 1985 do not have one. I have written about the neutral wire requirement separately. Some kits also require a specific companion switch and will not work with the existing traveler wiring until you re-terminate it. Ironically, you need to understand the old wiring to install the smart version correctly.
The energy savings are also smaller than the packaging suggests. A stairway light with two 9 watt LED bulbs used for an hour a day uses about 0.54 kWh a month, close to 10 cents at 18 cents per kWh. A smart switch drawing around half a watt on standby, all day and night, uses about 0.36 kWh a month, roughly 6 cents. On a light that small, the switch can add more than half the running cost back. If the attraction is scheduling or motion control, fine. If the attraction is the electricity bill, the numbers do not work.
What to do once you know which wire goes where
If you are confident with basic switch replacement and have checked the power is off, the fix for a swapped common is short. Move the common wire to the dark screw. Put the two travelers on the brass screws, in either order, because the travelers are interchangeable. Connect the bare or green ground to the green screw. Fold the wires back neatly, mount the switch and restore power.
Then test all four combinations in the table above. If any combination fails, check the other switch for the same mistake. If both switches are correct and it still fails, there may be a loose connection in a junction box or at the light, and that is a job for an electrician.
One thing to do this week, even if your switches work fine: take a photo of the wiring each time you open a switch box, and stick a small label inside the box noting which wire is the common. Whoever replaces that switch next, you included, will thank you.
FAQ
Does it matter which traveler goes on which brass screw?
No. The two traveler terminals are interchangeable. Only the common, on the dark screw, must be in the correct place.
Why does my 3-way switch only work when the other switch is up?
Almost always because the common wire is on a traveler terminal at one of the switches. It often happens after one switch is replaced.
Can I use a regular switch in place of a 3-way switch?
Not in a three-way circuit. A single-pole switch has no traveler terminals, so the other switch will stop controlling the light.
What cable do I need between two 3-way switches?
Three-conductor cable with ground: 14/3 on a 15 amp circuit or 12/3 on a 20 amp circuit.
More in Outlets and Wiring
Outlets and Wiring
Knob and Tube Wiring and What It Means for Your Home
A reader wrote to me about a 1928 house where the ceiling lights had started to flicker and the hallway smelled faintly of hot...
Outlets and Wiring
Switched Outlet Wiring and How to Make It Always On
A reader wrote to me last winter about a living room outlet in a house built in 1974.
Outlets and Wiring
Outlet Not Working and the Safe Checks to Try First
You plug in a lamp, nothing happens, and the breaker panel shows every switch in the on position.