Retro Consoles and CRT TVs: The Electrical Risks Worth Knowing
Retro gaming has brought a lot of old electrical equipment back into homes. Consoles from the 1980s and 1990s, their original power adapters, and the heavy CRT televisions that make old games look the way they were meant to are being...

Retro gaming has brought a lot of old electrical equipment back into homes. Consoles from the 1980s and 1990s, their original power adapters, and the heavy CRT televisions that make old games look the way they were meant to are being pulled out of lofts and bought at car boot sales. Many of them are now thirty or forty years old, older than most of the wiring rules that would apply to them if they were made today.
I like this hobby, and I have a Super Nintendo of my own. But I have also seen what can go wrong: a melted adapter, a scorched console board, and one near miss with a television that a friend decided to open "just to clean it". Most of the risk comes from three places, and only one of them is something an ordinary owner should try to deal with alone.
The CRT television: the part I would not open
A cathode ray tube television works by firing electrons at the inside of the screen, and to do that it uses very high voltages. The anode connection on the back of the tube typically runs at somewhere between 20,000 and 30,000 volts on a domestic set. The tube itself acts as a capacitor, and it can hold a dangerous charge for days or even weeks after the set has been unplugged.
That is the point people miss. With most appliances, unplugging makes them safe to open. With a CRT, it does not. The charge sits on the tube, at the end of a thick red or black lead with a rubber cap called the anode cup. Touching the wrong place can deliver a painful and potentially dangerous shock, and the reflex jerk away from it has caused serious injuries on its own.
Repair technicians discharge the tube with a specific tool and procedure before working inside. I am not going to describe that procedure here, because the honest advice for a homeowner is not to open a CRT at all. If the picture needs adjusting, the geometry is wrong or the set needs cleaning inside, take it to someone who repairs them. They are becoming harder to find, but retro gaming communities usually know who is still working locally.
Unplugging a CRT does not make it safe to open. It only stops it getting worse.
From the outside, a CRT is reasonably safe to use, with two cautions. The ventilation slots on top must stay clear, because the sets run warm and dust on the internal boards is a fire risk in older units. And a set that crackles, smells of burning or shows a picture that shrinks and flickers should be switched off at the wall and checked. Those are the same warning signs we list in electrical warning signs you should never ignore.
Power adapters: the most common problem
Old consoles mostly used external power adapters, and those adapters are where I see the most trouble. Consoles of that era did not share a standard. The original NES ran on an adapter supplying 9 volts AC, not DC. The Super Nintendo used 10 volts DC. The first Sega Mega Drive used 9 volts DC with the centre pin negative, the reverse of many other devices. Plug the wrong adapter into the wrong console and you can damage the board, even if the plug fits.
Adapters also age. The cables near the plug and near the adapter body crack after decades of bending, exposing the inner wires. Some transformer-based adapters from that era run hot by design, and after thirty years the insulation inside may have degraded. I have seen two with scorch marks on the casing.
My advice here is firm: replace original adapters rather than trusting them. Modern replacements built for specific consoles are inexpensive, usually lighter, and have protections the originals never had. Keep the original in a drawer if you are a collector. Use the new one.
Imported consoles and the voltage trap
Many collectors buy Japanese consoles, which are often cheaper and sometimes have better games. Japan's mains supply runs at 100 volts. North America uses around 120 volts. The UK and most of Europe use 230. A Japanese adapter plugged into a UK socket through a simple plug converter receives more than twice its rated voltage, and it can overheat or fail within minutes.
The fix is either a step-down transformer rated for the right voltages and with enough capacity, or, more simply, a modern adapter made for your own country's mains that supplies the correct DC voltage and polarity for the console. A plug converter changes the shape of the pins and nothing else. It is the most common mistake I hear about from retro collectors, and it is entirely avoidable.
Inside the console: what is reasonable to do yourself
Unlike a CRT, the inside of a cartridge console runs at low voltage once the adapter is unplugged. Cleaning cartridge contacts with isopropyl alcohol, replacing a worn power switch, or swapping the coin-cell battery that keeps save games in old cartridges are all within reach of a careful hobbyist.
The one internal job that needs more thought is capacitor replacement, often called recapping. Electrolytic capacitors dry out or leak with age, and some handhelds such as the Sega Game Gear are well known for it. Leaking capacitors can corrode the board. Replacing them involves soldering and correct orientation, since electrolytic capacitors are polarised. Fitting one backwards can make it fail violently when powered. If you have never soldered before, this is a good job to learn on a scrap board first, or to hand over. Our guide to when an electrical job is safe to DIY applies the same logic.
A simple setup that keeps it safe
Once everything is working, the remaining risks are the ordinary ones. Run the console, the CRT and any upscaler from one good-quality surge-protected strip rather than a chain of old adapters. Switch everything off at the wall when you finish playing, since old adapters draw power and get warm even when the console is off. We explain why surge protection matters for games kit in the case for surge protection.
If you are in the UK and selling or lending equipment, a PAT test from an electrician is a reasonable step for anything with an original mains lead. It is not legally required for private sales, but it protects the next owner.
Before you plug it in again
Take every adapter for your retro consoles and read its label. Note the output voltage, whether it is AC or DC, and the polarity symbol. Compare each against the rating printed on the console it powers. Check the cables for cracks near both ends. Anything with damaged cable, scorch marks or a mismatched rating should be replaced with a modern adapter before the next session, and any imported console running through a plug converter should stay unplugged until it has the right supply.
More in Games
Games
What Keeps Online Game Servers Running
When an online game loads instantly at three in the morning and a result lands on time to the second, it is easy to forget how...
Games
What Online Game Overheat Warnings Teach About Overloaded Sockets at Home
Plenty of games have a heat gauge. Push an engine, a weapon, or a reactor too hard and a meter climbs toward red, a warning...
Games
How Game Generator Builds Teach About Backup Power
Survival and base-building games almost always reach a point where you build a generator and decide what it will keep alive...